IMG_20170722_094109.jpg
This is what she originally looked like![]()
IMG_20170722_094109.jpg
This is what she originally looked like![]()
912 IS
Airmaster Prop
Garmin Stack
C-FKLO
I think since I'll be recovering and painting already, it's a good time to swap them out. I never put ethanol in my tanks but you never know if an accident etc. might happen.. I heard good and bad about sloshing but if had the chance I would just replace them now. .
If the one wing is fine, I'll just cut out the tank area and pop the tank in. The other one I'll probably completely remove. The tail too.Wow! Great project. I recommend to strip the fabric off the wing to determine any damage not visible from the outside. While at that, strip the other wing and replace tanks to ensure there will be no problem later. Also, on the vertical stabilizer, after stripping off the fabric you can inspect to ensure there is no more damage there.
I think I have those all in my Super Sport manual but I will be thoroughly checking everything. I actually think the bent tube up top came from him putting his hand on the bar to brace himself as he flipped over, but it for sure warrants further inspection!Josh, I'd recommend getting the main jigging points from Kitfox - i.e. wing pickup points, MLG pickups, tip of the vertical fin etc..
Thanks for all the great information! I'm just mulling over if I want to change the firewall forward now or if it will be fine as is. I'm not a huge fan of the two piece cowl set up. I guess with that swing chicken missing, you can't make an extended baggage area? I will probably enlarge the elevator if it hasn't been already since I'm covering and painting already.Fun project! You are indeed correct the engine mount was moved a few inches forward in the series 7 to help with CG when filling the baggage compartment...
The plastic header tank is in it but I will be replacing that. I think I get what you are saying about the rudder. Is it worth lengthening the horns? To answer the rest of your questions, from pictures it looks like: It has a heater, not sure about oil thermostat but the oil cooler is located just below the prop flange. Oil reservoir is in the center against the firewall. The coolant rad is on an angle mounted to some weird sheet metal baffle just below the engine. Looks like the baffle might actually be the firewall. It has adjustable rudder pedals, and the trim switch looks to be in the same location as my model 7. It has a 912ULS in it.
Yes I believe the only make the 7SS FWF now but it bolts on the extact same. The Model 6 was a different design originally. I'm potentially interest in your flapperon! Let me know if it's the right side and how much you think you want for it!I think some of the differences from 6 to 7 depend on when the items were purchased. Mine is a 6 and when I got the FF forward kit in the fall I'm sure I was told it's the same as the 7. Nothing it mounted, so i can always take pics or measurements for you.
Also, I may have an extra flapperon (not sure which side off hand) if you want to take a look. It has a bit of damage to the skin where the hinge tore through it from being compressed during travel.
Thanks for the info and questions everyone!
------------------
Josh Esser
Flying SS7
Rotax 914iS
AirMaster Prop
Edmonton, AB, CWL3
------------------
Josh Esser
Flying SS7
Rotax 914iS
AirMaster Prop
Edmonton, AB, CWL3
OK, we picked up the plane and got it home. The plane is in better shape than I hoped. The spars are fine with no dings. The one wing has two bays of trailing edge that need to be replaced, and a few loose false ribs on the outboard end. Really a testament to the strength of this wing. The wing tips COULD be salvage able if you were good at Fiberglass-Reinforced which I'm not...
The rudder tail post is straight and undamaged but the foam tip got all smashed so the fabric still needs to be removed and that fixed.
Right now I'm leaning towards removing ALL the fabric from the wings so I can really inspect the wing and recover. I'm really not looking forward to that process but I think it will be cheap piece of mind.
I definitely need to order a new strut and a new flapper for the right side.
------------------
Josh Esser
Flying SS7
Rotax 914iS
AirMaster Prop
Edmonton, AB, CWL3
Gonna put Oratex on the wings?
Probably not. I’ll probably be recovering the entire plane and I can do that for about half the price of Oratex. Don’t get me wrong. I think it’s a cool product but the fact that some people having issues with it, coupled with the fact that covering is a weak spot for me, I figure I’ll stick with what I know since they don’t have the colour I want anyway!
------------------
Josh Esser
Flying SS7
Rotax 914iS
AirMaster Prop
Edmonton, AB, CWL3
Great find! Glad your not finding it in worse shape. Should be a great plane after you massage the hurts out of it!![]()
"Somebody said that carrier pilots were the best in the world, and they must be or there wouldn't be any of them left alive." Ernie Pyle
Brett Butler
Flying: N46KF, 1998 Model 5 Outback, 912ul 110hp, G3x with 2 axis a/p, Beringer wheels & brakes, SS7 firewall forward, NR prop, Custom paint