Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Results 1 to 8 of 8

Thread: Straightening groves gear

  1. #1

    Join Date
    Jul 2018
    Location
    albury australia
    Posts
    14

    Default Straightening groves gear

    Hi all,

    I’m looking for info and experience from anyone that may know if it’s possible to rebend groves kitfox 5 gear?Aircraft suffered a ground loop.

    Many thanks

    James
    australia

  2. #2
    Super Moderator Av8r3400's Avatar
    Join Date
    Jan 2009
    Location
    Merrill, WI
    Posts
    3,044

    Default Re: Straightening groves gear

    It can be straightened, but then needs to be re-heat treated. Your best bet is to contact Grove Aircraft and discuss it with them to see if it is cost effective over just replacing the spring.
    Av8r3400
    Kitfox Model IV
    The Mangy Fox
    912UL 105hp Zipper
    YouTube Videos

  3. #3

    Join Date
    Dec 2011
    Location
    Boulder Creek, CA
    Posts
    55

    Default Re: Straightening groves gear

    He is Down Unda, try a local spring fabrication shop. Plenty of hot rodding down there, gotta be a spring shop or two.

  4. #4
    Super Moderator Av8r3400's Avatar
    Join Date
    Jan 2009
    Location
    Merrill, WI
    Posts
    3,044

    Default Re: Straightening groves gear

    Not any spring shop can work with aluminum springs. Call Grove.
    Av8r3400
    Kitfox Model IV
    The Mangy Fox
    912UL 105hp Zipper
    YouTube Videos

  5. #5
    pakitdvr's Avatar
    Join Date
    Jun 2013
    Location
    Lancaster pa
    Posts
    24

    Default Re: Straightening groves gear

    Had same problem cost and time to do wasn’t worth it. Got new. Grove hear schedule can be very long

  6. #6
    Senior Member
    Join Date
    Aug 2016
    Location
    Melbourne, Australia
    Posts
    642

    Default Re: Straightening groves gear

    Quote Originally Posted by Av8r3400 View Post
    It can be straightened, but then needs to be re-heat treated. Your best bet is to contact Grove Aircraft and discuss it with them to see if it is cost effective over just replacing the spring.
    Totally agree. You don't know what aluminium alloy it is nor what heat treatment it's been through after forming. I assume you're insured and if so, why aren't the insurers paying for it ?.
    David
    SS7 Builder

  7. #7
    Senior Member
    Join Date
    Jan 2011
    Location
    LAWRENCE, KS
    Posts
    479

    Default Re: Straightening groves gear

    Last time I talked to Grove about straightening my used gear, they told me my gear was the older aluminum type with they don't use anymore, and to heat treat it they would have to change the settings on their oven and run my gear through by itself,,,,at great cost. However, if you have the newer type gear, it would be cheaper to re-heat treat than the older.
    Hope this helps
    Roger

  8. #8

    Join Date
    Jan 2011
    Location
    mi
    Posts
    59

    Default Re: Straightening groves gear

    Yep you can do. You will have to cold bend it. Do not heat it up to bend it back you will soften the gear but it can be bent back. Bolt to steel table and use a hydraulic port a power unit takes a lot to bend it into the right pace but can be done .

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •