So my manual states rib lacing is optional - but has anyone actually taken that option? Has anyone used alternate methods of securing the fabric to ribs? Just curious.
So my manual states rib lacing is optional - but has anyone actually taken that option? Has anyone used alternate methods of securing the fabric to ribs? Just curious.
If I recall correctly, the manual hints that it may not be required, but strongly recommends that you do it. There's no good reason not to do it.
I've taken 2 Poly Fiber classes and read the manual about a thousand times, and the advice is always the same: You should mechanically attach your fabric to the ribs no matter how wide your capstrips are or what the manual says. Having done this, I'll say it was not difficult, and didn't take that long. It took me about 15 minutes per rib, including threading the needle and transitioning between ribs. In my opinion, once you get going, it's actually one of the more enjoyable parts of the build. Don't be intimidated. Just get some practice and do it.
Edit: watch this about 17 times while sitting with some kind of practice rig. You'll be growing palm trees in no time.
--Brian
Flying - S7SS
My build manual said that too.
However, the Polyfiber manual says you must mechanically attach because the force that will remove the fabric from the rib is a peeling force and the width of the rib is irrelevant.
I agree that the riblacing became enjoyable once I got the hang of it and it really did not take that long.
I saw one Kitfox years ago that did not appear to have any lacing but I know nothing about the owner or how it held up.
Maxwell Duke
Kitfox S6 IO-240 Built it (Flying since 2003)
Maule M7-235C Sold it (liked it though)
RV-10 IO-540 Bought it
Zenith CH-750 Built with 7 friends (DAR Vic Syracuse)
Google Steve Wittman. Wikipedia states his wings were improperly built. It is my understanding that his fabric was not laced. Don't hold me to that piece of info though. None the less, Brian is correct, no good reason to leave out the laces and I agree it was fun. If your going to build an airplane yourself, build an airplane and do it with safety in mind first and foremost.
Eddie Forward
Flying
SS7, 912iS, Garmin G3X
Right, mechanically attached. Has anyone tried alternates to stitching? It's not about the time or anything. I'm just curious.
The Avid Magnum used staples that curled as they went in so they would hold more. No doubt, that would be fast and easy. Maybe not near as good the second time around with a bunch of holes in the capstrips, and it would probably be hard to get the staples out when you are stripping the fabric. Probably most of the early Avids and Kitfoxes did not ribstich. I've had 4 Avids and one Kitfox that weren't ribstiched with no problems. I did ribstich the Avid and Kifox 4 wings when I recovered them though. Partly because I already had the materials from when I bought a bunch of left over stuff from some one else supplies. It also does take the worry out of things, and maybe would help in case of resale. Besides, as others have said, it's not that hard or time consuming once you get at it. JImChuk
Yes, I used flat, waxed rib stitching cord with the Oratex. Measured off a length, scraped a thumbnail along the cord followed by pulling through a rag wetted with alcohol. This was just to remove some of the excess wax. After stitching, there were a couple of flakes of wax on a few of the knots but they were clean for the most part. Only took a couple of minutes to wiped everything with alcohol. Brushed glue along the reinforcing tapes and made sure the lacing got wet. The finishing tape stuck without problem and there are nice sharp creases along the laces so adhesion is good.
I agree, this is a very satisfying step of the covering process.
Carl Strange
Flying
SS7, 912iS, Oratex, G3X
Same approach and results as Carl.
- Gary
S7 SuperSport Tri-gear
w/Rotax 912, Oratex, Dynon
I got a reply from oratex. They suggest that if your manual says stitch then stitch - for obvious liability reasons IMO. But, I was also told that gluing to the ribs should be more than adequate as well.
If your ribs are stamped construction and do not have a turned down edge, you need to produce chaffe strips from your Oratex material and glue them to the ribs. Do not use any other store bought chafe strip material as it will not work with Oratex. Remember to glue the final Oratex covering to the Oratex chafe strips.