I did my rudder with no stiffeners only to find out the humidity caused them to swell and warp. In my opinion, stiffeners are not optional unless you are bonding it to something along side it.
I did my rudder with no stiffeners only to find out the humidity caused them to swell and warp. In my opinion, stiffeners are not optional unless you are bonding it to something along side it.
------------------
Josh Esser
Flying SS7
Rotax 914iS
AirMaster Prop
Edmonton, AB, CWL3
Half (just under) of the horizontal stab done. I need to go glue the ribs with weldments through them. Was waiting to hear/see back from you guys. Dinner, then trimming the ribs for the other side.
After gluing, I went upstairs to show neighbor wings and fuselage, and noticed that KF uses a lot of adhesive to bond the wing ribs in. Did I use enough adhesive to bond in my ribs?
Tomorrow, I will install stiffeners on today’s work and install ribs in the other half.
Last edited by Flyboy66; 06-09-2018 at 05:33 PM.
By all means, use stiffeners on all ribs not otherwise stiffened by a steel structural member. The kit typically does not include enough stiffener material so you will be tempted to skip it on some ribs, but go buy some 1/8" ply from the local hobby shop and cut some more. I skipped some on my elevator and was sorry I did. The fabric shrink process pulled the outer steel tubing in just enough so that some of my unstiffened ribs took on an "S" curve. Not a show stopper, but not good in my book.
Jim Ott
Portland, OR
Kitfox SS7 flying
Rotax 912ULS
I am sold on stiffeners, but it raises another question. How do you clamp the stiffener in place while the adhesive sets?
Any pictures?
The outboard 8 ribs are now installed on the stab. Tomorrow is stiffener day as well as elevator rib day. Also, what about foam versus balsa wood for the outer edge of the stabilizer?
I used small spring clamps to hold the stiffeners.
I highly recommend balsa rather than foam on the stabilizer tips as well as the elevator tips. Much more resistant to hangar rash in these very vulnerable places. Foams OK on the top of the rudder and vertical stab.
Jim Ott
Portland, OR
Kitfox SS7 flying
Rotax 912ULS
Recommend you also put stiffeners on the elevator ribs. I didn’t on mine initially and had to go back and do it because they bowed with moisture uptake over time. Suggest you Put the stiffeners on ribs first before you locate and bond in place.
David
SS7 Builder
I just put a bit more flox in to make sure gravity didn't take advantage of the situation. I put the stiffener on and just wrapped tape around it in a couple spots along the length. Everything turned out well.
I too would recommend Balsa wood. I won't ever use foam anyplace if I do this again. I have mentioned before, If your using Oratex, foam will melt when forming the fabric around those surfaces.
Eddie
Eddie Forward
Flying
SS7, 912iS, Garmin G3X
Steve - after bonding in the ribs in my VS, and then adding the stiffeners, I changed the process a bit when doing the rudder. I first "dry fitted" the ribs (using the ribs in the VS for alignment), then added the stiffeners using a table top to ensure a flat rib, and then bonding them in their final resting places.
As you can see in the pictures, I'm fond of using my most used tool - clamps from the aviation department in Harbor Freight.
Bonding while on the table top also made the job tons easier due to access.
More details can be seen on my build site.
See my build log at:http://www.mykitlog.com/lowandslow/
I stiffened all of the HS ribs, but since I didn't have enough material, I did not do the elevator ribs, as they were all nice and straight. Tightening the fabric was enough compression on the steel structure that most of them bowed a little. Fortunately, the elevator ribs follow a linear contour from LE to TE, and you actually can't tell in the finished product, but I wish I would have stiffened them.
You can get this adhesive and a much cheaper non-branded gun from McMaster Carr. I just used mine for the first time, and now that I've seen the light, I would have used this from the beginning despite the cost. You'll need to order a half ton of applicator tips, but you will waste very little adhesive. My glue work does not look as good as John's, but it would have if I'd used this gun from the beginning. Also really nice not to have to mix. Just put the tip on and go!Get the ratcheting gun with dubble barel syringes with mixing tips if your looking for great filets. If I remember from my visit in April, Brandon has an air driven applicator gun with mixing tips.
--Brian
Flying - S7SS
I used the glue gun on some later items in my build. I ran out of the expensive mixing tips, but continued to use the gun without the tips. It squirted out a nice accurate 50-50 ratio onto a piece of cardboard that I then mixed by hand. Not as handy as with the tips, but still much better than the mess of using the big cans.
Jim Ott
Portland, OR
Kitfox SS7 flying
Rotax 912ULS