Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Results 1 to 9 of 9

Thread: Dielectric Thermal Paste

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Senior Member jiott's Avatar
    Join Date
    Jun 2010
    Location
    Portland, OR
    Posts
    2,960

    Default Dielectric Thermal Paste

    I'm going nuts over the proper use of dielectric or thermal paste. I have a tube of thermal heat sink paste, the label says it is dielectric, thermal heat transfer paste; most commonly used to get good heat transfer between a microchip and a heat sink. Now I have heard several people, on this forum, say this stuff is also good to use on wiring terminals and contacts to get a good electrical bond and prevent corrosion at the joint. But when I read the definition of a "dielectric" it says that means it is an insulator. Won't this stuff actually prevent electrical contact and be very bad to put on a ground terminal, etc.

    Some of you professional "Sparkys" out there please help me with this.
    Jim Ott
    Portland, OR
    Kitfox SS7 flying
    Rotax 912ULS

  2. #2
    Senior Member rv9ralph's Avatar
    Join Date
    Aug 2014
    Location
    Greenleaf, ID
    Posts
    618

    Default Re: Dielectric Thermal Paste

    I am as confused as you. I too looked up dielectric and read the same definition. Then I looked up a photo I have of the product I use for my plugs, and on the bulleted list of what it is it states both:
    "High Dielectric Strength" and "Superior Conductive Quality"
    Although in this usage it could mean heat conductive, but on the front it states
    "Excellent for automotive electrical applications, i.e. Alternator, regulators and rectifiers."

    Go Figure!

    Ralph

  3. #3
    Senior Member Av8r_Sed's Avatar
    Join Date
    Feb 2010
    Location
    10C Greenwood, IL
    Posts
    671

    Default Re: Dielectric Thermal Paste

    Straight dielectric grease is a silicone based product. Thermal heat sink compound or thermal paste has a similar base but have fillers(often zinc oxide) to give it superior heat transfer properties.

    Dielectric grease is clear, while heat transfer compound is usually white or silver due to the fillers.

    I use dielectric grease to protect wiring connections from oxidation, such as battery terminals - as a topical treatment after I tighten the connection. I also use it to protect and rejuvenate rubber products such as carburetor and spark plug boots.

    I use the thermal compound between my voltage regulator and it's heat sink as well as on spark plug threads. The trick with this stuff is to use it sparingly. More is not better. It also makes a big mess if you get it on other stuff.
    -- Paul S
    Model III SN910
    582 IVO Med

  4. #4
    Senior Member jmodguy's Avatar
    Join Date
    Jul 2014
    Location
    Carmel, IN
    Posts
    744

    Default Re: Dielectric Thermal Paste

    I would not use thermal paste unless you need to transfer heat. The automotive use mentioned is for high heat parts, i.e. regulator and rectifier to pull heat away from the electronic part and shed it to a metal heat sink more efficiently. And Av8r is correct in that it is very messy, no matter how neat you think you are!
    If you want to seal an electrical connection with something like RTV, make sure you use an electronics grade RTV. Standard RTVs contain acids that can cause corrosion in some metals of electrical connections.
    Make sure all connections are made BEFORE applying the sealant!
    Jeff
    KF 5
    340KF

  5. #5
    Senior Member
    Join Date
    Mar 2009
    Location
    Pittsboro,NC
    Posts
    299

    Default Re: Dielectric Thermal Paste

    According to my A&P, also use thermal paste on spark plug threads. In my 2 stroke days I always used the silver anti-seize. It always worked just fine as far as I knew. My old plugs always came out easy enough. I never knew that "heat transfer" was an issue. I always replace my spark plugs when we do my annual and do the compression check. It's pretty cheap insurance. My A&P is super anal about doing everything by the book and I'm glad he is. My 912 runs like a fine Swiss watch. He uses the same thermal paste that he uses on the GA stuff. I'm sure Spruce and the other parts suppliers carry it. I'll look it up. James Thomas

  6. #6
    Senior Member jmodguy's Avatar
    Join Date
    Jul 2014
    Location
    Carmel, IN
    Posts
    744

    Default Re: Dielectric Thermal Paste

    OK I was curious so I looked up "spark plug thermal paste". Many of the returns were Rotax specific. Unless I read it wrong it looks like the main reason for using thermal paste on spark plugs is for plugs that have a picky heat range. The paste should be from the top of the threads to about midway down.
    I have never heard of using thermal paste on plugs before... huh.... Learned something today!
    Jeff
    KF 5
    340KF

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •