Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Results 1 to 3 of 3

Thread: Balancing a Whirlwind Prop

  1. #1
    Senior Member
    Join Date
    Nov 2019
    Location
    Leavenworth WA
    Posts
    651

    Default Balancing a Whirlwind Prop

    Thought I would follow up on my efforts to balance my 75" Whirlwind after P.Johnson reminded me that it's better to have the tape on the prop than the backing plate. I had come to that conclusion and had moved my DynaVibe reflective tape from my spinner backing plate to my blade but never followed up on my build log. Here are the takeaways from my balancing experience.

    My first issue was that my results weren't repeatable. I would run up my prop with no weights and get a set of numbers for vibration. Then I would do the exact same thing 10 minutes later and get different numbers. As in not even in the same Zip code kind of different numbers. Thought it might be the backing plate flexing some so modified my mount for the tach so that it was now higher up, moved my reflective tape from the back plate to the blade and the numbers became relatively repeatable. The second thing I ran into was getting a set of numbers that said to put a half ounce weight at a position, running the engine again and the next set of numbers said to put another half ounce at another position around 120 degrees from the first. Run it a third time and get a whole new position for another half ounce that was within around 45 degrees of the first position. Was literally chasing my tail here. Sent DynaVibe my datasheet from my runs and asked for some help on what they thought might be the issue. To get the weight size, I was using the numbers in the instructions that said it took around 50gr for every ips. The DynaVibe guys (who were really helpful and got back to me right away with questions and suggestions) said that it looked to them like my prop was "very light" and that the 50gr number was a starting point for any number of different props. That the 50g number was probably a bit too heavy for the lighter, carbon fiber blades. I should try determining weight size using 30gr/ips. That was the ticket. Pulled all the aforementioned weights and started over. Was balanced to .02ips in three runs using a quarter oz weight and an eighth oz weight and was able to repeat the results a couple times over a couple days.

    Hope this helps someone reading the instructions and thinking they are chasing their tails. Pics are of my modified install for the sensors.

    Gary

    DynaVibe Mod 1.JPGDynaVibe Mod 2.JPG
    Gary (Geek) Phenning
    Leavenworth (Not the Prison), WA
    Kitfox STi N68SG

  2. #2
    Senior Member Delta Whisky's Avatar
    Join Date
    Dec 2017
    Location
    Amissville, VA
    Posts
    660

    Default Re: Balancing a Whirlwind Prop

    Gary - a very valuable write up. Will bookmark it for sure. Thanks for taking the effort.

  3. #3
    Senior Member
    Join Date
    Nov 2019
    Location
    Leavenworth WA
    Posts
    651

    Default Re: Balancing a Whirlwind Prop

    Quote Originally Posted by Delta Whisky View Post
    Gary - a very valuable write up. Will bookmark it for sure. Thanks for taking the effort.
    Thanks Darrel. I know I have gotten a lot more good info/suggestions from the forum than I have given. Maybe it will help the next guy

    Gary
    Gary (Geek) Phenning
    Leavenworth (Not the Prison), WA
    Kitfox STi N68SG

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •