Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Exhaust mounting holes are getting worn on a 912

  1. #1
    Senior Member fastfred's Avatar
    Join Date
    Nov 2016
    Location
    herkimer,ny
    Posts
    217

    Default Exhaust mounting holes are getting worn on a 912

    My exhaust springs wearing the attachment holes. Does anyone one know of a fix to stop this before it wears through?

  2. #2
    Senior Member Dave S's Avatar
    Join Date
    Oct 2008
    Location
    St Paul, MN
    Posts
    1,866

    Default Re: Exhaust mounting holes are getting worn on a 912

    Fred,

    My DAR (also an EAA tech counselor) advised me that both the springs and holes will wear (if left to their own devices) due to high frequency vibration common to the engine.

    His advice even before I fired the engine was to lay a bead of red RTV on both sides of each spring over the coils. A second piece of advice is to run a length of safety wire through the holes in the tabs and through the spring coming back on the outside (to keep the junk together if one breaks.

    To date - neither the springs nor the holes have worn noticeably.

    PS - disregard the spark gap note on the rocker arm cover - I have since changed to a smaller gap.
    Attached Images Attached Images
    Dave S
    Kitfox 7 Trigear (Flying since 2009)
    912ULS Warp Drive

    St Paul, MN

  3. #3
    Senior Member fastfred's Avatar
    Join Date
    Nov 2016
    Location
    herkimer,ny
    Posts
    217

    Default Re: Exhaust mounting holes are getting worn on a 912

    Thanks I did that last year and it seems like that made it wear even more. I wondered I there was and insert that could be put in there. We might have to machine one for it.

  4. #4

    Join Date
    Oct 2018
    Location
    Kitchener, Ontario
    Posts
    127

    Default Re: Exhaust mounting holes are getting worn on a 912

    Solid brass rivet than drill it out for the spring ! Worked on my Rotax 503 for my flex wing trike, I later switched to ball joint clamps

  5. #5

    Join Date
    Jul 2018
    Location
    Portland,OR
    Posts
    4

    Default Re: Exhaust mounting holes are getting worn on a 912

    I’ve got the same wear going on. I need to amend it since the wear is getting pretty advanced. Is there an alternative to getting it welded? Any hardware ideas? A flanged bushing insert? I see the rivet idea. Any others?

  6. #6
    Senior Member Maverick's Avatar
    Join Date
    Mar 2017
    Location
    Phoenix
    Posts
    295

    Default Re: Exhaust mounting holes are getting worn on a 912

    If the wear is on the tabs, what about welding an A.N. washer to each side of the tab? Not sure if it would be all that easy but seems like it would strengthen the holes. There's not much can be done to the springs.
    EAA, AOPA
    KF5 (N49FK & N36KJ)
    Phoenix, AZ

  7. #7

    Join Date
    Jul 2018
    Location
    Portland,OR
    Posts
    4

    Default Re: Exhaust mounting holes are getting worn on a 912

    Quote Originally Posted by Maverick View Post
    If the wear is on the tabs, what about welding an A.N. washer to each side of the tab? Not sure if it would be all that easy but seems like it would strengthen the holes. There's not much can be done to the springs.
    I thought about just that!
    However, I pulled the exhaust and am having a welder replace the older style sheet steel flanges with the newer style rod loops. Problem solved but no plane to fly on nice weekend!

  8. #8
    Senior Member
    Join Date
    Apr 2009
    Location
    Chisholm Mn
    Posts
    1,600

    Default Re: Exhaust mounting holes are getting worn on a 912

    To late now that you have pulled the exhaust, but what about drilling another set of holes further down on the tabs, use longer springs, and then when or if they get worn down, put new tabs or doublers on the sides of the existing ones. That would probably double the time before you have to address the issue. JImChuk

  9. #9
    Senior Member jrevens's Avatar
    Join Date
    Aug 2009
    Location
    Arvada, CO
    Posts
    2,172

    Default Re: Exhaust mounting holes are getting worn on a 912

    I wonder if periodically lubricating those wear points with a high-temp lubricant would make a difference. Perhaps working in a little anti-seize grease,.. or maybe a few drops of of a graphite or moly- containing lube like Loctite every so often. Has anyone tried that? Loctite might be better since it would probably attract less dirt after the carrier evaporates, leaving the graphite. Maybe some other dry-film lubricant such as Dow 321 would be even better.
    John Evens
    Arvada, CO
    Kitfox SS7 N27JE
    EAA Lifetime
    Chap. 43 honorary Lifetime

  10. #10
    Senior Member PapuaPilot's Avatar
    Join Date
    Nov 2013
    Location
    Nampa, Idaho
    Posts
    1,252

    Default Re: Exhaust mounting holes are getting worn on a 912

    Quote Originally Posted by avidflyer View Post
    To late now that you have pulled the exhaust, but what about drilling another set of holes further down on the tabs, use longer springs, and then when or if they get worn down, put new tabs or doublers on the sides of the existing ones. That would probably double the time before you have to address the issue. JImChuk
    I think this is a great idea. We have done similar repairs on certified aircraft.

    I don't think John's idea would make much of a difference.
    Phil Nelson
    A&P-IA, Maintenance Instructor
    KF 5 Outback, Cont. IO-240
    Flying since 2016

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •