Register
Help
Remember Me?
What's New?
Activity Stream
New Group Messages
New Events
Mark Forums Read
Forum
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Groups
Groups
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
Yesterday,
07:11 PM
famo
replied to a thread
Damien's build
in
Members' Build Logs
Thanks Brett, I'm going with Poly Fiber process and will finish with Aerothane. I haven't settled on a design yet, but...
see more
4 replies | 236 view(s)
Yesterday,
05:33 PM
famo
replied to a thread
Damien's build
in
Members' Build Logs
Thanks folks. I have a 3" wide tape that I'm going to cut down to 2" wide except for that small area. That will give me...
see more
4 replies | 236 view(s)
Yesterday,
02:48 PM
D&CJohnson
replied to a thread
Dan & Cole's 1050 Build
in
Members' Build Logs
It is a little gut wrenching tearing up someone elses hard work, but the wood fairings had to go. Lots of chiseling,...
see more
27 replies | 3014 view(s)
Yesterday,
02:36 PM
D&CJohnson
replied to a thread
Damien's build
in
Members' Build Logs
I bought some thread from my polyfiber distributor for sewing envelopes. If it were me I would use a needle and...
see more
4 replies | 236 view(s)
Yesterday,
12:23 PM
JoeRuscito
replied to a thread
Constant Speed Prop - $7500
in
Classifieds
Hey Victor, based on Duc's marketing materials it should be good up to 160HP. The link below if you click on the "quick...
see more
2 replies | 121 view(s)
Yesterday,
11:56 AM
VictorV
replied to a thread
Constant Speed Prop - $7500
in
Classifieds
What engine(s) will it support? I have a 915is. Victor
see more
2 replies | 121 view(s)
Yesterday,
11:03 AM
VictorV
replied to a thread
Auto pilot servos.
in
Electrical/instruments/avionics
One thing to consider is you can install the mounting plates and wiring for the servos and install the servos later. If...
see more
6 replies | 472 view(s)
Yesterday,
10:03 AM
Stu Pierce
replied to a thread
October 2024 Production Slot Available
in
Classifieds
SOLD Admin please delete thread.
see more
4 replies | 444 view(s)
10-31-2024,
04:05 PM
jorgy
started a thread
912is rpm drop when shutting down lane B
in
Engines
if I shut down lane B the engine will lose approximately 1500 rpm and run rough. i have no lane faults or fuel pressure...
see more
0 replies | 52 view(s)
10-31-2024,
09:36 AM
jrevens
replied to a thread
Turtle deck hinge question.
in
Kitfox general discussion
Me too! I also haven?t seen any cracking or embrittlement of the hinge. It is advertised as ?UV resistant?. My...
see more
6 replies | 639 view(s)
10-31-2024,
09:28 AM
desertdave
replied to a thread
Model 5-7 Gear
in
Classifieds
I am willing to break up this package $500 for the gear plus shipping $1000 for the wheels/brakes/axles plus...
see more
1 replies | 279 view(s)
10-31-2024,
09:03 AM
tjohnson
replied to a thread
Forward Lift Strut Fabric Reinforcement Plate
in
Factory Build/Support Videos
Thank you for the pics and info.. Appreciate it
see more
2 replies | 118 view(s)
10-30-2024,
08:38 AM
rtc183
replied to a thread
Turtle deck hinge question.
in
Kitfox general discussion
Really? I use mine all the time.
see more
6 replies | 639 view(s)
10-29-2024,
07:14 PM
bbs428
replied to a thread
Forward Lift Strut Fabric Reinforcement Plate
in
Factory Build/Support Videos
Refer to this link in my build thread. I think it may address your question. bbs428 Build - Page 7 (teamkitfox.com)...
see more
2 replies | 118 view(s)
10-29-2024,
04:33 PM
Sink Rate
replied to a thread
Cold air intake for 912is
in
Kitfox general discussion
I see it a bit differently. I am really quite happy with the change and I had to pitch the prop a bit steeper. After...
see more
10 replies | 2807 view(s)
10-29-2024,
01:26 PM
tjohnson
started a thread
Forward Lift Strut Fabric Reinforcement Plate
in
Factory Build/Support Videos
Hello folks Can someone post a picture of.the proper Placement of the forward lift strut fabric reinforcement Plate?...
see more
2 replies | 118 view(s)
10-29-2024,
10:52 AM
dothedr3w
replied to a thread
New Garmin Experimental Radios
in
Electrical/instruments/avionics
Garmin GTR 205 / GNC 215 16W Enablement Card $1959 CAD....yikes. I guess 10W is gonna enough for this lil fella.
see more
1 replies | 111 view(s)
10-29-2024,
10:44 AM
dothedr3w
started a thread
New Garmin Experimental Radios
in
Electrical/instruments/avionics
Few months old now, but Garmin has discontinued the following radios: - GTR 200 (panel mount) - GTR 200B (panel...
see more
1 replies | 111 view(s)
10-29-2024,
10:10 AM
dothedr3w
replied to a thread
Auto pilot servos.
in
Electrical/instruments/avionics
I had a Dynon avionics suite planned for the longest time before I eventually switched to Garmin; one of the reasons...
see more
6 replies | 472 view(s)
10-29-2024,
12:52 AM
bbs428
replied to a thread
Damien's build
in
Members' Build Logs
Finish tape will cover nicely and reinforce the weak area. Agreed that 1/2 inch on the right is marginal. If...
see more
4 replies | 236 view(s)
More Activity
No More Results
No Recent Activity